Toontoys Forums Forum Index Toontoys Forums

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

60 series tilt steering column in a 40 series cruiser

 
Post new topic   Reply to topic    Toontoys Forums Forum Index -> Technical Information
View previous topic :: View next topic  
Author Message
fj-rankenstein
moderator


Joined: 06 Dec 2003
Posts: 4209

PostPosted: Tue Dec 07, 2010 2:19 am    Post subject: 60 series tilt steering column in a 40 series cruiser Reply with quote

i have really wanted tilt steering in Rankenstein for a long long time so i thought this was going to be an easy mod and jumped right into it.. it didnt end up that way and i needed a little while to think about things.. i came up with this over the last week.. it was a pain in the ass but now that i have most everything worked out, i wont hesitate doing this again..


the "pocket" that gets bolted to the fire wall had to get the inside enlarged so the end of the steering column could get through.. the final hole ended up being cut around all 4 welded nuts in the pocket and resembled a cross.. this was so not only could i get the end of the steering column shaft through the hole but the u-joint from the column.. everything just squeeks through..


here is a little closer pic..


this is the template that i made using the base from the original steering column.. this will be the plate that gets welded to the end of the 60 series column..


this is the plate being built.. the 4 holes i think were drilled to 3/8's and the center hole was 2 inches..


this is the final product built.. i had to cut it in half so i could get it around the steering column end.. from here i put the 60 series column to where it looked like it would work and installed the two halves around the column shaft in the firewall pocket..


i will have to get a pic of what the steering column looked like before.. where the springs for the tilt column mechanism hook up, the whole area had a lot of excess metal that flared out making it tough to put into the stock colomn location in the firewall.. a lot of trimming was done to make this work and then that cross brace was rewelded.. this is a very much needed step to make this work.. this cross piece will also serve as a mount for the brake pedal return spring.. the original mounting hole was cut off when i enlarged the column mounting bracket..


you can see how much i had to cut out of the column support based on the shiny grinded metal.. i wasnt pleased with how low the column was sitting under the dash so i cut and trimmed in small doses till i was able to get it up enough to where it was in the stock columns location.. sorry, no before photos..


here is another..


and another..


here is the column removed again for final welding of my square base plate..


and another..


and here it is bolted up in its home.. i still have to sand blast and paint all the associated parts but i am still just test fitting everything at this point..


and one more from the inside.. although it doesnt look like much, its been a pain in the butt to get to this point.. i think that column has been in and out of the truck over 40 times..


and the result.. all the way down.


and all the way up..



here is the piece of tubing that i used to extend the front nose of the steering column. i needed the column to be 1.5 inches longer


here it is all in place for yet another test fit.. i was quite happy to be at this point..


here is a small 1/4 inch washer that i welded to the top of the column so the spring for the tilt lever would have something to hook onto..


this is another test fit with the column in the dash.. you can see how tight everything is.. the other spring peeking through towards the back is the brake pedal return spring.. it will now get hooked onto here..


and here is one of the "wings" that i welded to the side of the column so it can be bolted to the underside of the dash..


pretty much the last test fit and final assembly shot.. very happy with how it turned out..


closer shot of the same thing


a good underdash shot of everything bolted up..


there is one thing that i didnt cover but will speak of briefly.. the steering shaft inside the column had to be extended 1.5 inches.. basically there are 2 plastic pins that i drilled out.. these pins hold the steering shaft a pre-determined length and are meant to easily break and let the column collapse.. there is quite a bit of shaft to easily and safely extend the shaft to almost twice its lengths of about 6 inches or so.. i only needed 1.5 inches of extension.. i then re-drilled two small holes and replaced the plastic pins with a couple of tiny roll pins.. i tested to see if they would indeed break and allow the shaft to collapse and then did with only a little more force..
_________________
"If you need a tool and don't buy it, you will ultimately find that you have paid for it but don't have it". -Henry Ford

my yard looks like a toyota dealership circa 1980
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Toontoys Forums Forum Index -> Technical Information All times are GMT - 7 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group
Protected by Anti-Spam ACP